Custom TFT LCD Solutions for Industrial, Medical, Automotive and Smart Applications
Products
- View as
10.1 Inch 1024x600 LVDS TFT LCD Module 16:9 - VXT101MBAH-02
The VXT101MBAH-02 is a 10.1-inch TFT module with a 4-lane LVDS interface — the differential interface in our range. At 1024x600 with 16.7M colours, a parallel RGB bus would need around 28 signal lines switching at pixel-clock rates; LVDS carries the same payload over four data pairs and one clock pair, ten wires, with lower emissions and tolerance of real cable distance. It is a native 16:9 panel with a 222.72 x 125.28 mm active area, 380 cd/m² and 500:1 contrast. It needs five supply rails and 1.17 MB of external frame memory. Rated -20 to +70°C.
Read MoreSend Inquiry
1.6 Inch 400x400 Round TFT LCD Module QSPI Interface - VXT016VCSA-01
The VXT016VCSA-01 is a 1.6-inch round TFT module with a QSPI interface — the only module in our range with a four-lane serial pixel bus. Small round displays usually want a serial interface because pins are scarce, but 400x400 is 160,000 pixels and single-lane SPI struggles to move a full frame; QSPI carries four bits per clock, roughly four times the throughput at 62.5 MHz, while still using only four data pins. It is also the smallest and densest panel we make at 1.6 inches and 255 PPI with square pixels. ST77903, 16.7M colours, 3.0 V backlight needing no boost, -20 to +70°C.
Read MoreSend Inquiry
10.4 Inch 800x600 TFT LCD Module 4:3 Industrial Anti-Glare - VXTA40CAH-01
The VXTA40CAH-01 is a 10.4-inch TFT in 4:3 — the format industrial and medical equipment has been built around for twenty years. Its active area of 211.2 x 158.4 mm is the standard 10.4-inch size, so it drops into a cutout originally cut for a panel of this class, and legacy software written for 800x600 does not letterbox. It is bright at 650 cd/m² typical with a 520 minimum, uses an anti-glare polarizer for factory lighting, and ships without touch so it pairs directly with our 10.4-inch capacitive touch panel. The documentation is also unusually complete: ten reliability test items each citing its IEC and GB standard, a 50,000-hour MTBF, and inspection criteria given in millimetres. 24-bit RGB on 60 pins, -20 to +70°C.
Read MoreSend Inquiry
10.1 Inch 1280x800 IPS TFT LCD Module with Capacitive Touch MIPI - VXTA10BXH-01C
The VXTA10BXH-01C is a 10.1-inch 1280x800 TFT with an integrated capacitive touch panel, driven over 4-lane MIPI DSI. Against our 10.4-inch 800x600 module it carries 2.1 times the pixels through 35% fewer pins — 39 instead of 60, and 32 functional instead of 43 — because four differential pairs move the whole image. Touch is on the module with an FT5426, so there is no separate flex to route. The backlight has PWM in and PWM out, so dimming is handled on the module rather than in your firmware. It is 16:10 at 150 PPI, anti-glare, with 80° viewing in all four directions and no gray scale inversion — together the signature of an IPS cell. Contrast is 700 minimum. The document has real problems, listed here: an active-area figure that does not reconcile, a touch controller with no I2C pins, and a brightness figure with no minimum.
Read MoreSend Inquiry
10.1 Inch 1280x800 MIPI TFT LCD Module 2.9mm Without Touch - VXTA10BXH-01
The VXTA10BXH-01 is the display-only version of our 10.1-inch 1280x800 MIPI panel. It shares the active area, resolution, 39-pin connector and 4-lane MIPI interface with the VXTA10BXH-01C but omits the capacitive touch layer — and what that buys is the point: 2.9 mm thick against 5.15 mm, and an outline of 229.6 x 149.3 mm against 238.60 x 160.6 mm. If touch is handled elsewhere or not needed, you are not paying for a layer you will not use. It is also the version with complete documentation: a luminance minimum of 200 cd/m², a ten-item reliability programme citing IEC and GB standards, an MTBF of 50,000 hours, and inspection to MIL-STD-105E at AQL 0.65. It runs -20°C to +70°C, ten degrees wider than the touch version, and states the active area as 216.96 x 135.6 mm, confirming the correction we derived on the sibling.
Read MoreSend Inquiry
7 Inch TFT LCD Module with Custom Cover Glass and Sensor Openings - VXT700MYIA-03C
The VXT700MYIA-03C is a 7-inch front panel assembly: a display and touch stack under a custom cover glass carrying three functional openings — a camera window, a proximity sensor window and a microphone through-hole. The ink over the openings is specified with a number you can measure: visible light transmittance at 520 nm below 25%, which is what lets the proximity sensor hide behind the glass while still passing IR. Everything runs on one 40-pin flex at 0.30 mm pitch, and that flex carries the LED backlight as well, so there is one connector rather than two. The glass has an anti-fingerprint coating, there is black electromagnetic shielding on both sides, and the section gives a 2.25 mm finished stack with component height capped at 1.8 mm. This is a mechanical drawing, so the page is explicit about what is not in it: no resolution, interface, pin assignment, optical or environmental data.
Read MoreSend InquiryWhy Source TFT LCD Modules from Victronix
Victronix has been designing and manufacturing TFT LCD modules for 20 years, supplying standard and custom displays to customers in industrial control, medical, automotive and smart home markets.
Wide Range, One Supplier
- Sizes from 0.96inch to 32inch
- Resolutions from QVGA to FHD
- Interfaces: SPI, RGB, LVDS, MIPI DSI, HDMI with converter board
- Panel options: TN, IPS, high brightness, transflective, bar type, round
Customization Built Around Your Project
- Custom FPC length, pinout and connector
- Resistive or capacitive touch panel integration
- Cover glass with custom printing, thickness and surface treatment
- Brightness upgrade and wide temperature design
- Interface conversion boards
Quality You Can Verify
Every module is tested for brightness, contrast, viewing angle and response time before shipment, and validated against thermal shock, humidity and vibration requirements. Our management systems are certified to ISO 9001, ISO 14001 and IATF 16949 within the scope of the applicable certificates.
From Sample to Volume
Standard samples ship in 15 working days. Engineering support covers datasheet, 3D drawing, interface definition and driver reference code. Low MOQ for prototypes, scalable capacity for volume production.
