China 5 inch 800x480 TFT LCD module Manufacturer, Supplier, Factory

The VXT101MBFH-01 is a 10.1-inch TFT LCD module with 1920 x 1200 pixels — WUXGA, the interface is dual-channel LVDS and contrast carries a stated 700 minimum against 800 typical. Brightness is 300 cd/m² typical with no stated minimum.

The VXT121QXHA-01 is a 12.1-inch TFT module with 1024 x 768 pixels, and it is the only 4:3 panel in our 12.1-inch range — the other two are 1280 x 800. That matters because XGA in a 4:3 layout is what a very large installed base of industrial controllers, medical instruments and test equipment was designed around, and it remains the usual target when a display in existing hardware has to be replaced. The active area is 245.76 x 184.32 mm with pixels that are square to ten decimal places, so circles and dial scales stay true. Brightness is 1000 cd/m², the highest figure we publish in this size, and the viewing angle is 85° in all four directions with no stated best direction. The interface is 4-lane LVDS on a 20-pin connector, and it runs from a single 3.3 V rail — no separate gate or analogue supplies to generate. We are equally direct about what this module demands and what is not yet documented: the backlight draws about 14 W, which is over 90% of the module's total power and needs a real thermal plan; brightness and viewing angle are given as typical values without stated minimums; and the driver IC, outline dimensions and LVDS data mapping are not in the file we hold.

The VXT016VCSA-01 is a 1.6-inch round TFT module with a QSPI interface — the only module in our range with a four-lane serial pixel bus. Small round displays usually want a serial interface because pins are scarce, but 400x400 is 160,000 pixels and single-lane SPI struggles to move a full frame; QSPI carries four bits per clock, roughly four times the throughput at 62.5 MHz, while still using only four data pins. It is also the smallest and densest panel we make at 1.6 inches and 255 PPI with square pixels. ST77903, 16.7M colours, 3.0 V backlight needing no boost, -20 to +70°C.

The VXT430BPSA-04 is a 4.3-inch TFT LCD module with 480x272 resolution and a true 24-bit RGB888 interface, supplied without touch. It shares its entire electrical and mechanical platform with our VXT430MPSA-16 and differs in one figure: a 20,000-hour backlight instead of 50,000. That makes it the choice where a display can be serviced easily — supervised indoor equipment, machine panels, instruments — rather than unattended installations where a service visit costs more than the panel. Rated -30 to +80°C.

The CTP-T350GF-04 is a 3.5-inch capacitive touch panel in G+G construction, and the only portrait panel in our range — a 48.96 x 73.44 mm view area in a true 2:3 shape, matched to 320x480 displays and to our 3.5-inch portrait TFT module. It is also the only panel whose I/O runs down to 1.8 V, so a 1.8 V-logic host can drive it without a level shifter. An FT5446 controller handles five-point touch over I2C. Built for handheld instruments, wall controllers, elevator panels and portable medical devices.

The CTP-VX156B5544-GG is a 15.6-inch capacitive touch panel in G+G construction, built for laptop-class and portable equipment rather than fixed kiosks. Note for buyers: at 15.6 inches it is inspected in the 10.1–17 inch cosmetic tier, which is about 25% stricter than the tier used for 21.5-inch and larger panels. Transmittance is at least 85% with ≥6H hardness, response is ≤12 ms, and it draws just 12–14.5 mA — low enough for battery-powered devices. Suited to portable terminals, medical carts, industrial laptops and handheld HMI.