China VXT280GQSW-01 Manufacturer, Supplier, Factory

Victronix 5.7 inch 640×480 TFT Module offers a high typical brightness of 1000 cd/m² and a typical contrast ratio of 450:1, ensuring excellent readability from various viewing positions. Secondly, it supports 18-bit RGB parallel digital and SYNC (HSYNC/VSYNC) & DE modes. Besides, it features a 21-die White LED backlight with a lifetime of 30,000 to 50,000 hours (retaining 50% brightness), ensuring clarity and usability in various lighting conditions. It also undergoes rigorous tests, including high/low temperature storage and operation, temperature cycling, humidity, vibration, and shock. Consequently, it can operate effectively across an extensive temperature range of -20°C to +70°C. This Victronix 5.7 inch TFT display is widely used in Factory automation HMI, medical monitors, test & measurement equipment, transportation systems, and embedded control panels requiring sunlight-readable, high-reliability displays.

The VXT350CQH-05 is a 3.5-inch 320 x 240 QVGA TFT LCD module, and two things about it are worth knowing before anything else. It is 3.2 mm thick, the thinnest module in this range on the same 76.90 x 63.90 mm footprint, and it carries no touch panel - so if your product has a separate touch solution, or none, you are not paying for one. The backlight is confirmed twice over: the mechanical drawing shows the LED circuit as six dies in one string from LEDA to LEDK, and 19.2 V over six gives exactly 3.20 V per LED, while the stated 0.384 W matches 19.2 V x 20 mA exactly. Response time is also better documented than usual, with both Ton and Toff published and floors on each - 15 and 30 ms on, 35 and 50 ms off - and contrast carries a 200 minimum. Two things need settling before you commit. This is a TN panel: the specification states a 12 o'clock viewing direction with grey-scale inversion at 6 o'clock, and vertical angles of 50 and 60 degrees, so mounting orientation has a right answer - if your product is handheld and the orientation is not under your control, ask us about a panel with no preferred direction. And the timing chapter runs three pages and is published entirely as diagrams, with a note saying the sequences are for reference only and referring you to the HX8238D data sheet, so there is nothing in this document to configure a controller from.

The VXT350PNO-01P is a 3.5-inch 480 x 272 TFT LCD module with a 4-wire resistive touch panel, Resistive sensing responds to pressure rather than to a finger's conductivity, so it works with gloves, wet hands, a stylus or a tool tip - which is why it remains the choice for industrial and medical equipment. The backlight is the most trustworthy figure in the document, because it is confirmed three independent ways: the block diagram states the circuit as 1 * 6LED, six in series; 19.2 V over six gives exactly 3.20 V per LED, which is the typical forward voltage the electrical table states; and the connector carries one cathode and one anode, which is what a single string looks like. Reliability is equally solid - nine tests, all at 240 hours, with a stated 50,000-hour MTBF.

The Victronix VXT700WRA-01 is a 7.0-inch TFT LCD module with 800 x 480 pixel resolution and support for up to 16.7M colors, built for embedded and industrial equipment that needs a compact, easy-to-drive display. Its 24-bit parallel RGB interface with DE (data enable) and DCLK lets most mainstream MCUs and MPUs — STM32, NXP i.MX, Allwinner, Rockchip and similar — drive the panel directly from their on-chip LCD controller, with no LVDS serializer or bridge chip and no extra BOM cost. The module runs from a single 3.3 V logic supply, uses an RM53052 / RM57452 driver IC, and is rated for a -20°C to +70°C operating range, so it works in unheated enclosures and outdoor cabinets.

The VXT700TOSA-01 brings a circular display format to digital dials, status indicators and distinctive product interfaces. Its 1080×1080 resolution and 4-lane MIPI connection support detailed graphics designed around a central focal point.

This Victronix 3.5 inch 320×240 QVGA IPS TFT Module with a 24-bit RGB interface. This TFT LCD module designed for robust and reliable operation in demanding industrial and embedded applications. Combining a sharp QVGA resolution with vibrant color performance and a wide viewing angle, this module delivers exceptional clarity for user interfaces, instrumentation, and control systems. As a professional manufacturer and supplier of TFT modules in China, this Victronix 3.5 inch TFT Module is fully compliant with ROHS environmental standards, ensuring superior application performance. We offer a customized service to meet the needs of our customers.