China ILI9881 TFT LCD Manufacturer, Supplier, Factory

The Victronix VXT700WHA-02P​ is a 7.0-inch 800 × 480 TFT LCD module with a touch panel, driven by MOS_CHIP_G424A​ over an 18-bit parallel RGB interface on a 40-pin 0.5 mm Hirose FH19-40S-0.5SH connector. The reason to look at it is the interface freedom.​ A MODE pin selects between DE mode and SYNC mode, so it works with hosts that emit DE and hosts that emit only HS and VS. L/R and U/D give hardware scan inversion.​ And full numeric timing is published​ — 860 clocks by 528 lines at 27.2 MHz, which is exactly 60 Hz.

Victronix 9 inch 1024×600 IPS TFT Module offers a typical brightness of 500 cd/m², wide viewing angles of 85° in all directions, and a contrast ratio of 800:1, ensuring excellent readability from various angles. Secondly, it supports a LVDS interface with 6-bit/8-bit mode selection (SELB pin control). Besides, it features a 3S13P white LED system with a lifespan of 20,000 to 50,000 hours at half brightness, ensuring long-term use in various industrial applications. In addition, it is validated through thermal shock (-30°C↔80°C), vibration (10-55Hz), mechanical shock (100G), and ESD protection (±2kV HBM) to operate reliably in extreme temperatures (-20°C to +70°C). This Victronix 9 inch LCD is perfect for Industrial Control, Automobile Device, Medical Equipment, Smart Home, Marine Electronics, Fitness Equipment, POS Terminal, ATM Machine, Vending Machine, etc.

The VXT430GWH-02 is a 4.3-inch IPS TFT module in portrait orientation: 480 x 800 pixels over an active area of 56.16 x 93.60 mm, taller than wide, with a diagonal of 4.2975 inches. It is the only portrait module and the only IPS module in our 4.3-inch range. Being IPS means viewing angle is 80° typical in all four directions with no preferred direction and no gray scale inversion to design around — decide orientation on mechanical grounds alone. Pixel pitch is 0.117 mm square, giving 217 PPI, so small text stays legible and circular graphics need no correction. It runs 24-bit RGB over a 42-pin connector driven by an HX8369A, with a serial port on the same connector for configuration. Brightness is 310 minimum, 350 typical and 390 maximum cd/m² — the lowest in the family and intended for indoor and handheld use, published as a complete range you can design and inspect against. At 2.15 mm it is also the thinnest 4.3-inch module we offer.

This 3.9-inch 480x128 TFT module is a bar display — a 3.75:1 stretched panel, the only one of its shape in our range — and the brightest module we make at 1000 cd/m² typical. A narrow strip suits a line of text, a row of readouts or a status bar, and 1000 cd/m² keeps it legible under strong light. It is transmissive with 16.7M colours, an ST7282A driver and an ALL viewing direction, so mounting can be decided mechanically. A full frame is only 120 KB, so most microcontrollers need no external RAM. Rated -20 to +70°C.

The CTP-VX121B5563-GG is a 12.1-inch capacitive touch panel in G+G construction with a 1.8 mm cover glass — the thickest in our range, about 1.6 times the usual 1.1 mm — bonded to the sensor with 0.2 mm SCA rather than a foam gasket. That combination is built for unattended and high-abuse installations. Transmittance is at least 85% with ≥6H hardness, and the total stack is 2.7 mm. Suited to industrial HMI, outdoor kiosks, transport terminals and medical equipment.

The Victronix VXT700WRA-01 is a 7.0-inch TFT LCD module with 800 x 480 pixel resolution and support for up to 16.7M colors, built for embedded and industrial equipment that needs a compact, easy-to-drive display. Its 24-bit parallel RGB interface with DE (data enable) and DCLK lets most mainstream MCUs and MPUs — STM32, NXP i.MX, Allwinner, Rockchip and similar — drive the panel directly from their on-chip LCD controller, with no LVDS serializer or bridge chip and no extra BOM cost. The module runs from a single 3.3 V logic supply, uses an RM53052 / RM57452 driver IC, and is rated for a -20°C to +70°C operating range, so it works in unheated enclosures and outdoor cabinets.