China 800x1280 portrait display Manufacturer, Supplier, Factory

The VXT350MLH-03P is a 3.5-inch 320 x 240 TFT LCD module with a 4-wire resistive touch panel, and resistive sensing works with gloves, wet hands or a stylus. The brightness 200 cd/m2 minimum with the touch panel fitted, contrast 300 minimum and NTSC 50% minimum - and because brightness is also published without the touch panel at 300 cd/m2

The VXT121QXHA-01 is a 12.1-inch TFT module with 1024 x 768 pixels, and it is the only 4:3 panel in our 12.1-inch range — the other two are 1280 x 800. That matters because XGA in a 4:3 layout is what a very large installed base of industrial controllers, medical instruments and test equipment was designed around, and it remains the usual target when a display in existing hardware has to be replaced. The active area is 245.76 x 184.32 mm with pixels that are square to ten decimal places, so circles and dial scales stay true. Brightness is 1000 cd/m², the highest figure we publish in this size, and the viewing angle is 85° in all four directions with no stated best direction. The interface is 4-lane LVDS on a 20-pin connector, and it runs from a single 3.3 V rail — no separate gate or analogue supplies to generate. We are equally direct about what this module demands and what is not yet documented: the backlight draws about 14 W, which is over 90% of the module's total power and needs a real thermal plan; brightness and viewing angle are given as typical values without stated minimums; and the driver IC, outline dimensions and LVDS data mapping are not in the file we hold.

The VXTA10BXH-01 is the display-only version of our 10.1-inch 1280x800 MIPI panel. It shares the active area, resolution, 39-pin connector and 4-lane MIPI interface with the VXTA10BXH-01C but omits the capacitive touch layer — and what that buys is the point: 2.9 mm thick against 5.15 mm, and an outline of 229.6 x 149.3 mm against 238.60 x 160.6 mm. If touch is handled elsewhere or not needed, you are not paying for a layer you will not use. It is also the version with complete documentation: a luminance minimum of 200 cd/m², a ten-item reliability programme citing IEC and GB standards, an MTBF of 50,000 hours, and inspection to MIL-STD-105E at AQL 0.65. It runs -20°C to +70°C, ten degrees wider than the touch version, and states the active area as 216.96 x 135.6 mm, confirming the correction we derived on the sibling.

The CTP-T430GF-04 is a 4.3-inch capacitive touch panel in G+G construction, sized for 480x272 displays and matched to the 95.84 x 54.66 mm view area of our 4.3-inch TFT module. It runs from two rails — VDD at 2.8–3.3 V and IOVCC at a fixed 3.3 V — and its 10-pin FPC puts VDD on pin 10 rather than pin 2. Rated -10 to +60°C, it is built for indoor and commercial equipment rather than industrial extremes. EETI EXC3146 controller, five-point touch.

The VXT700TOSA-01 brings a circular display format to digital dials, status indicators and distinctive product interfaces. Its 1080×1080 resolution and 4-lane MIPI connection support detailed graphics designed around a central focal point.

The VXT430HPWA-03C is a 4.3-inch TFT LCD module with 480x272 resolution and integrated capacitive touch, wired as two independent subsystems: the display runs on its own 40-pin interface and VDD rail, while the FT5446 touch controller has a separate 6-pin FPC and its own VDD-CTP supply. That lets you power the display down and keep touch alive, or reset touch without touching the display. Rated 850 cd/m² and -30 to +85°C, it suits outdoor handheld terminals, field instruments and portable equipment.