China TFT LCD with LED backlight Manufacturer, Supplier, Factory

This Victronix 5 inch Capacitive Touch TFT Module is a high-performance 5 inch TFT-LCD module integrating a capacitive touch panel (CTP), designed for industrial HMI, embedded systems, and interactive applications. Combining an 800 × 480 RGB pixel display, 16.7M color depth, and robust environmental compliance, this RoHS-certified module delivers exceptional clarity and reliability. As a professional manufacturer and supplier of TFT modules in China, Victronix 5 inch TFT Module is fully compliant with ROHS environmental standards, ensuring superior application performance. We offer a customized service to meet the needs of our customers.

The VXT350LQZ-01P is a 3.5-inch 320 x 240 QVGA TFT LCD module with a 4-wire resistive touch panel, and the touch specification is the reason to look at it. Section 6 publishes what almost nothing in this size does: linearity of +/-1.5% after environmental and life testing, terminal resistance per axis, insulation resistance of 20 megohms minimum, response time under 10 ms, light transparency of 78% minimum, operation force of 80 gf typical, surface hardness of 3H minimum, 100,000 pen sliding cycles and 1,000,000 hitting cycles - with the test conditions for each. Two other figures are unusually trustworthy. Brightness carries both a floor and a ceiling, 280 minimum and 420 maximum around the 350 typical, so you can see the production spread as well as the worst case.The viewing angles are the narrowest in our range at 25 degrees typical on one horizontal side and 45 everywhere else, and while the specification states a 6 o'clock viewing direction, it is the horizontal pair that is asymmetric rather than the vertical one - so confirm the orientation with us and expect a narrow cone.

The VXT430GWH-02 is a 4.3-inch IPS TFT module in portrait orientation: 480 x 800 pixels over an active area of 56.16 x 93.60 mm, taller than wide, with a diagonal of 4.2975 inches. It is the only portrait module and the only IPS module in our 4.3-inch range. Being IPS means viewing angle is 80° typical in all four directions with no preferred direction and no gray scale inversion to design around — decide orientation on mechanical grounds alone. Pixel pitch is 0.117 mm square, giving 217 PPI, so small text stays legible and circular graphics need no correction. It runs 24-bit RGB over a 42-pin connector driven by an HX8369A, with a serial port on the same connector for configuration. Brightness is 310 minimum, 350 typical and 390 maximum cd/m² — the lowest in the family and intended for indoor and handheld use, published as a complete range you can design and inspect against. At 2.15 mm it is also the thinnest 4.3-inch module we offer.

The VXT350FPQI-01 is a transflective, sunlight readable 3.5-inch TFT module for equipment that moves between indoor and outdoor light. Outdoors it reads by reflected light, and the backlight can be switched off entirely rather than merely dimmed, removing the largest load in the module. It is the third transflective panel in our range and the only one you can drive over a 3-wire SPI from an ordinary microcontroller — 240x320 portrait, square pixels, ILI9341V, 0.384 W backlight. Rated -20 to +70°C with ±8 kV air ESD.

This Victronix 3.5 inch 320x240 Wide Temperature IPS TFT Module is a high-performance 3.5 inch TFT LCD module engineered for demanding applications. Featuring a sharp 320×RGB×240 resolution and a bright 1000 cd/m² transflective display with anti-glare coating, it delivers excellent visibility even in challenging lighting conditions. As a professional TFT module manufacturer and supplier in China, this Victronix 3.5 inch TFT Module is strictly compliant with the ROHS environmental standards to provide superior application performance.

The VXT177SSI-02 brings color graphics to compact equipment with a 1.77-inch TFT display and an 8-bit MCU interface. Its small footprint provides an option for handheld instruments, portable devices and simple menu-based control panels.